As a new kind of green building interior wall plaster leveling material, plastering gypsum is widely used in building interior wall gypsum nowadays because of its good workability, good water retention, good adhesion, cement slurry hydration and strong alkali combination. Therefore, it is doubtful to increase the related problems of plastering gypsum, such as: how to use plastering gypsum? How many times have you scraped the plaster? How thick is the mortar? Wait a minute! To solve these problems, please.

　　灰泥主要用于建筑內墻混凝土、加氣混凝土、磚灰墻及天花板灰泥找平?；A課程治療:為了保證公司債券之間的表面畫石膏和基礎課,掃帚和鋼絲刷等工具應該被用來清理漂浮的灰塵和碎片的基本課程,和修復和踢平的表面的凹凸部分基礎課程。確?；鶎痈蓛?、平整、堅實，確保抹灰后無空鼓、脫落等現象。如果基層松散或光滑，應使用標準稀釋滲透界面劑進行滲透壓實界面處理。如果底座太干，可以用水打濕墻面底座，但不能有清水。

　　The mortar is mainly used for building interior wall concrete, aerated concrete, brick mortar wall and ceiling mortar leveling. Basic Course Therapy: In order to ensure surface plaster and basic courses between corporate bonds, tools such as brooms and wire brushes should be used to clean up floating dust and debris, and basic courses to repair and flatten concave and convex surfaces. Ensure that the grass-roots is clean, smooth and firm, and that there is no empty drum and falling off after plastering. If the base is loose or smooth, the osmotic compaction interface should be treated with standard dilution osmotic interface agent. If the base is too dry, water can be used to wet the wall base, but not clear water.

　　濟南石膏粉:粉刷石膏怎樣用

　　Jinan gypsum powder: how to use plastering gypsum部署粉刷石膏漿:根據合適的粉水比(粉刷石膏粉:水= 4:1,實際的水比在實際施工一致性),加水攪拌桶,然后加入粉刷石膏粉,用電動攪拌機,混合無粉粉粉刷石膏漿達到所需的一致性,腌5分鐘,攪拌均勻后再批后方可施工。抹灰:每次抹灰厚度控制在5mm左右。抹灰厚度大的，應嚴格分層抹灰找平。根據抹灰部位確定抹灰順序?？梢韵葔禾旎ò澹賶簤Ρ?，先上后下(如果工人操作順利，也可以從底部向上擦拭)，從門的一側開始，從另一側退出，整個墻面連續工作?；炷撂旎ò蹇梢猿晒Φ赜没夷嗄ɑ?。如果平整度差太大，可以先擦底灰(薄而厚的刷膏膏)，然后再擦第二次壓光。第二次抹灰找平施工需要一層抹灰，抹灰層后設置好后，用刮尺沿著墻面垂直水平方向刮抹灰餅找平，直到找平為止，用木抹灰機搓毛壓實。

　　Deployment of plastering gypsum slurry: according to the appropriate powder-water ratio (plastering gypsum powder: water = 4:1, the actual water ratio is consistent in the actual construction), add water mixing barrel, then add plastering gypsum powder, use electric mixer, mix plastering gypsum slurry without powder to achieve the required consistency, marinate for 5 minutes, mix evenly before batch construction. Plastering: The thickness of each plastering should be controlled at about 5 mm. If the plastering thickness is large, the plastering level should be strictly stratified. The plastering sequence is determined according to the plastering position. You can press the ceiling first, then the wall, first up and then down (if the worker operates smoothly, you can also wipe from the bottom up), from one side of the door, from the other side to exit, the whole wall continues to work. Concrete ceilings can be successfully plastered with mortar. If the flatness difference is too big, you can first rub the bottom ash (thin and thick paste), and then rub the second calendering. The second plastering leveling construction needs a layer of plastering. After the plastering layer is finally set up, the plastering cake is leveled along the vertical and horizontal direction of the wall surface with a scraper ruler until leveling, and is rubbed and compacted with a wooden plastering machine.

　　1. 灰泥施工環境溫度應在5℃~ 35℃之間，養護溫度不低于0℃;2. 注意分配粉末狀膏體的水灰比，加水過多不易對墻體形成水波，加水過少不易施工且不易采光;2. 施工底漆灰泥不應透水，不應太濕;3.配制好的石膏膏應在初凝前使用，一般約1小時;4. 灰泥攪拌、涂刷工具用完后應及時清理干凈。

　　1. The ambient temperature of cement construction should be between 5 and 35 C, and the curing temperature should not be less than 0 C. 2. Pay attention to the water-cement ratio of powder gypsum, too much water is not easy to form water waves on the wall, too little water is not easy to construct and not easy to light; 2. Construction primer mortar should not be permeable and too wet; 3. Prepared gypsum should be used before initial setting. It usually lasts about 1 hour. 4. When the mortar mixing and brushing tools are used up, they should be cleaned up in time.

　　以上是濟南石膏粉廠家為大家整理的相關內容，想要了解更多內容，歡迎訪問網站：http://m.sjzmx.cnThe above is the related content of Jinan gypsum powder factory for you. For more information, please visit the website: http://m.sjzmx.cn.